桥式起重机金属结构疲劳计算新方法

本文介绍一种计算桥式起重机金属结构疲劳强度的新方法，探讨了结构应力幅的形成和分布，并以实例说明计算的全过程．     

雀替型阻尼器加固箍头榫木框架结构的抗震性能

为研究广府古建筑木结构的抗震性能及加固方法,采用菠萝格木材,设计并制作了两榀不同结构形式的典型广府木祠堂箍头榫框架,提出并制作了用于木结构榫卯节点加固的雀替型阻尼器,对雀替型阻尼器加固前后的木框架进行低周往复荷载试验,研究结构的抗震性能及阻尼器的加固效果。研究结果表明：阻尼器可以弥补初次加载产生的损伤,在转角不大时给残损的榫卯节点提供较高的初始刚度,并在榫卯节点自身开始闭合时与之协同受力,提高节点刚度、极限承载能力和耗能能力,使得加固试件的极限承载能力高于未加固试件;未加固试件经过加载,出现了榫卯脱离、榫卯局部压屈现象,加固试件的破坏形式主要为榫卯脱离、榫卯局部压屈和竖向顺纹劈裂裂缝;各节点的滞回曲线呈现明显的“捏缩”现象,榫卯节点强度退化系数均大于0.83,在循环荷载作用下表现出稳定的承载性能,随节点转角的增大,各节点的环线刚度、等效粘滞阻尼系数呈现逐渐减小并趋于稳定的趋势;边跨框架试件节点的等效粘滞阻尼系数逐渐稳定于0.1～0.2,而中跨框架试件节点的等效粘滞阻尼系数逐渐稳定于0.05～0.1,且经过阻尼器加固,边跨框架与中跨框架试件的总滞回耗能分别提高了67%和19%。     

块体金属玻璃微磨削加工的温度场仿真

建立单颗磨粒微磨削的正交切削模型和玻璃金属的本构关系方程,采用有限元工艺仿真系统对块体金属玻璃进行微磨削加工的温度场仿真,从而得到块体金属玻璃在微磨削过程中的温度以及温度变化趋势,进而观察其磨削温度是否达到块体金属玻璃的玻璃转变温度.因此,对玻璃金属磨削加工过程的温度仿真可以有效预测非晶表面是否有晶化现象的发生.改变微磨削加工参数,对块体金属玻璃的各个磨削区的温度变化趋势进行观察.通过仿真实验发现,块体金属玻璃的最高磨削温度发生在磨粒前刀面与磨屑接触的区域,即第二变形区.     

多层磁盒与涡流板电磁阻尼器性能研究

在研究了振动频率、运动幅值、涡流板厚度对电磁阻尼器性能影响的基础上,制做了多层磁盒与多层涡流板相间叠合而成的电磁阻尼器并进行了试验研究,即增大涡流板与磁盒接触工作面积对电磁阻尼器性能影响及能否提供较大阻尼力研究,结果表明：增大涡流板与磁盒接触面积阻尼力增大明显,说明电磁阻尼器可以提供满足工程需要的阻尼力,且体积不大、造价不高、性能较好。     

Super-plasticity of Zr<Subscript>64.80</Subscript>Cu<Subscript>14.85</Subscript>Ni<Subscript>10.35</Subscript>Al<Subscript>10</Subscript> bulk metallic glass at room temperature

Generally, bulk metallic glasses （BMGs） exhibit a very limited plastic deformation under a compression load at room temperature, often less than 2% before fracturing. In this letter, through an appropriate choice of BMGs＇ composition, an amorphous rod of Zr64.80Cu14.85Ni10.35Al10 with a diameter of 2 mm was prepared by using copper mold suction casting. X-ray diffraction and differential scanning calorimetry were utilized to determine its structure and thermal stability, and the uniaxial compression test was adopted to study its plastic deformation behavior at room temperature simultaneously. The results showed that the glass transition temperature and onset temperature of the exothermic reaction of the amorphous rod were 646 and 750 K, respectively, and its micro-hardness was 594.7 Hv. During compression, when the engineering strain and engineering stress arrived at 9.05% and 1732 MPa, respectively, i.e., the true strain and true stress reached 9.42% and 1560 MPa, respectively, the amorphous rod started to yield. After yielding, with the increase of load, the strain increased and the glass rod ulti- mately were compressed into flake-like form. Although the maximum engineering strain was larger than 70%, i.e., the maximum true strain exceeded by 120%, the amorphous specimen was not fractured, indicating that it has super-plasticity at room temperature. Through the appropriate choice of composition and optimization of the technological process, flexible BMG with super-plasticity at room temperature could be produced.     

Zr_(55)Al_(10)Ni_5Cu_(30)大块金属玻璃的晶化行为研究

分别在603 K、653 K、683 K、723 K、753 K、793 K和0.5 h、1 h、2 h、3 h、5 h的保温时间下对Zr55Al10Ni5Cu30大块金属玻璃进行了退火热处理.采用x射线衍射(XRD)法分析了退火后Zr55Al10Ni5Cu30大块金属玻璃的弛豫和晶化相析出的过程,计算了不同温度下结晶度和纳米晶粒尺寸的大小.通过差示扫描量热(DSC)法分析了Zr55Al10Ni5Cu30大块金属玻璃的热稳定性.Kjssinger曲线分析表明,Zr55Al10Ni5Cu30大块金属玻璃弛豫后晶化激活能高于其淬态的晶化激活能,退火温度对大块金属玻璃热稳定性有显著影响.     

A View on Wear Mechanism of Metallic Card Clothing

The wear mechanism of metallic card clothing, used in textile industry, was analyzed. A fast wear test for metallic card clothing racks was developed, which was used as collecting the wear metal particles. The failure type of card clothing was analyzed by the mean of scanning electron microscopy （SEM） and ferro-spectrum technology. The results show that the main wear mechanism of metallic card clothing is low load and high repetition interval fatigue wear caused by friction force between fiber and metal wire teeth. The appropriate quenching microstructure, which improves the wear resistance of the metallic card clothing rack is also discussed.     

快淬CoNiCu系列金属条带的巨磁电阻效应

研究了用快淬制备的铸态和退火处理后的颗粒合金膜Co 20NixCu 80-x(0≤x≤20)的结构、磁电阻性能.利用电镜观察到Co-Ni纳米颗粒在Co-Ni-Cu合金薄膜中分布均匀,与Co-Cu合金薄膜有不同.CoNiCu系列样品随Ni成分的增加,其相变过程由形核长大类型向失稳分解类型过渡.而且在室温下有比Co-Cu样品有更大的MR幅度.750 K下退火10 min的Co 20Ni5Cu 75快淬条带在300 K下的ΔR/R≌6.5%.     

挤压油膜柔性转子系统的优化设计

将优化设计方法应用于挤压油膜阻尼器－滑动轴承－柔性转子系统，从优化变量的选取、目标函数、约束条件等几方面来确定优化设计的数学模型，并将此模型应用于具体的实例中。计算表明，转子系统通过优化，能有效地改善系统运行的稳定性能。     

金属载体上原位合成ZSM-5分子筛

以正硅酸乙酯(TEOS)和NaAlO2作为硅源和铝源，四乙基氢氧化铵(TEAOH)作为模板剂，用水热合成法在经表面处理的金属载体上原位合成了ZSM-5分子筛涂层，并采用BET、XRD、SEM等表征技术，研究了金属材料的处理方法、合成时间及次数等因素对ZSM-5分子筛涂层的结晶度、比表面积、覆盖率和涂层热牢固度的影响。结果表明，用原位合成法可以在金属载体上制得结晶度高、热牢固度好的ZSM-5涂层。